This how-to guide provides a step-by-step process for making solar panels, from gathering materials to assembling the cells.
Key takeaways:
- Key Takeaway 1: The essential materials needed for building a solar panel include solar cells, substrate, tabbing wire, bus wire, soldering iron, encapsulant, diode, junction box, sealant, silicone, and a charge controller.
- Key Takeaway 2: To assemble the solar cells, lay them out in rows, connect them in series, solder tabbing wire across the bus bars, test the voltage output, affix them to the backing board with silicone sealant, and protect them with an encapsulant.
- Key Takeaway 3: Wiring the solar cells involves connecting them in series using tabbing wire and bus wire, adding a diode to prevent backfeed, testing each serial string for voltage output, and ensuring secure connections through soldering.
- Key Takeaway 4: Sealing the panel edges is important for protection, accomplished with a continuous bead of silicone sealant, allowing for proper curing, and periodic checks for seal integrity.
- Key Takeaway 5: Mounting the solar panel requires choosing a south-facing location with maximum sun exposure, tilting it at an angle equal to the latitude, using a mounting bracket for attachment, ensuring sufficient air flow for cooling, following local building codes and regulations, and consulting a professional for electrical connections.
Materials Needed for Building a Photovoltaic Solar Panel
To construct a photovoltaic solar panel, a specific set of materials are essential. First, solar cells are the core components that convert sunlight into electrical energy. These cells are typically made of silicon and can be purchased individually or in bulk, often pre-tabbed for convenience.
Additionally, a substrate is required to support the cells. Common choices include a non-conductive rigid material such as glass or plastic for the panel’s surface. For the backing, a sturdy material like plywood or metal adds durability and strength.
Further, tabbing wire and bus wire are necessary to connect individual solar cells together in a series to increase voltage and in parallel to increase current. A soldering iron and solder will ensure secure connections between wires and cells.
An encapsulant, such as EVA (ethylene-vinyl acetate), is used to protect the cells from environmental factors and maintain high light transmission. It’s crucial to choose a long-lasting encapsulant to ensure the panel’s longevity.
Finally, a diode is included to prevent reverse current flow, which can drain the battery at night, while a junction box will provide a location to connect the panel to an external circuit. Sealant and silicone are used to weatherproof the panel, and a charge controller will manage the power output to batteries or home circuits.
Selecting high-quality materials will lead to the efficient performance and extended life of the solar panel.
Assembling the Solar Cells
Start by laying out the solar cells in rows, aligning them to the size of the backing board, which acts as the foundation for your panel. Each cell must be connected in series, with the positive lead of one cell linked to the negative lead of the next, allowing for a cumulative voltage buildup.
Handle cells carefully as they are fragile. Use fine soldering techniques to join tabbing wire across the ‘bus bars,’ or silver strips, on each cell’s surface. Ensure enough overlap between cells for flexibility, and leave room at the edges of the panel to secure the cells in place.
For increased durability, consider purchasing pre-tabbed cells. When aligned properly, the tabbing wire extends beyond the edges of the cell. Once all cells are wired together, test the voltage output with a multimeter to verify the series is connected correctly before fixing the cells to the backing board.
Use a silicone sealant to affix each cell to the board, which should be a non-conductive and heat resistant material like glass or composite. This arrangement should then be covered with a clear, durable, and UV-resistant encapsulant to protect the cells from weather and mechanical damage.
Wiring the Solar Cells Together
Once solar cells are assembled, their wiring harnesses their collective power. Each cell has two wires: one from the top (negative) and one from the bottom (positive). Begin by flipping the cells upside down and soldering the positive wire from one cell to the negative wire of the next, creating a series connection. This boosts the voltage to match the battery bank.
To keep the current uniform and reduce power loss, use tabbing wire and bus wire—tabbing wire is thinner and connects cells in series, while bus wire is thicker to handle the increased current from multiple cells in parallel. For the uninitiated, parallel connection involves joining the positive wires together and the negative wires together, increasing the current but keeping the voltage the same as a single cell.
Employ a diode as part of the wiring system to prevent backfeed from the battery at night. Solder it on the positive side of the connection between the solar cells and the charge controller. Remember that consistent soldering and secure connections are vital to the panel’s efficiency and longevity. Use a multimeter to test each serial string of cells for the correct voltage output before moving on to the next step.
Sealing the Panel Edges
Sealing the edges of your solar panel is vital for protecting its internal components from environmental hazards such as moisture, dust, and debris. This prolongation of longevity is achieved by using a silicone sealant, which acts as a protective barrier.
When applying the sealant, ensure a continuous bead along the panel’s edges to eliminate any gaps. Allow the sealant to cure as per the manufacturer’s instructions before testing the panel outdoors.
Periodic checks for seal integrity can help maintain the panel’s efficiency over time.
Mounting the Solar Panel
After the assembly and sealing process, secure installation is the next step to ensure the panel’s efficiency and durability. Choose a stable and unobstructed location with maximum sun exposure. Typically, a south-facing direction is optimal in the Northern Hemisphere, while the reverse is true for the Southern Hemisphere. Tilt the panel at an angle equal to the latitude of its location to maximize solar absorption year-round.
Install a mounting bracket on the rear side of the panel; this aids in attachment to various surfaces. Consider a rooftop mounting system if space allows, ensuring it is compatible with your roof type and capable of withstanding environmental stressors. Alternatively, ground-mounted systems are a viable option, especially for larger installations. These should be anchored securely to withstand wind and weather conditions.
Ensure the mounting structure has sufficient air flow around the panel. Cooling is essential as temperature increases can lead to decreased panel efficiency. Leave a gap between the panel and the mounting surface to allow for air circulation.
Always follow local building codes and regulations when installing solar panels, as these may dictate specific requirements or restrictions. For electrical safety and optimal system performance, it is highly recommended to engage a professional for the panel’s electrical connection to your home’s power system.
